User Guide: XY-CD60 Battery Charge and Discharge Controller is a versatile digital battery control module designed to manage charging and discharging for batteries ranging from DC 6V to 60V
. It acts as a smart switch (relay) that automatically connects or disconnects based on voltage limits you set, preventing overcharging or deep discharging. 1. Key Specifications Voltage Range: DC 6V – 60V Control Precision: Output Type: Relay output (direct switch, does not convert voltage) HD LCD showing voltage, percentage, and time 2. Operating Modes The module has two primary modes. To switch between them, long press the UP button for 5 seconds XY-CD60 Solar Battery Charger Controller Module User Manual
You're looking for a manual guide for the XyCD60!
The XyCD60 is a popular CD player from a well-known brand, but unfortunately, I couldn't find a specific manual for this model. However, I can provide you with a general guide on how to use a typical CD player, which should help you get started with your XyCD60.
General CD Player Controls and Functions:
Basic Operations:
Additional Features (if available on your XyCD60):
Troubleshooting Tips:
If you need a specific manual for your XyCD60 or have questions about its unique features, I recommend:
is a versatile DC battery charge and discharge controller module designed for systems ranging from
. It is commonly used in solar setups to prevent battery damage from overcharging or deep discharging.
Below is a breakdown of the core functions and setup steps typically found in the XY-CD60 manual Core Operating Modes
The device functions in two primary modes depending on your wiring and settings: Charging Mode (UP):
The relay closes when the voltage falls below a set lower limit ( ) and opens when it reaches the upper limit ( cap U cap P ) to prevent overcharging. Discharging Mode (dn):
The relay closes when the voltage is above the upper limit ( cap U cap P ) and opens when it drops below the lower limit ( ) to prevent over-discharging. Quick Setup Guide Set Limits: Long-press the button to enter parameter settings. Use to toggle between cap U cap P (upper voltage limit) and (lower voltage limit). Adjust Values: Short-press to select the parameter, then use to adjust the voltage. Time Control (OP): You can set a specific charging/discharging time ( cap O cap P
). If the voltage doesn't reach the target within this time, the relay will automatically open. Long-press again to save and exit. Key Features Wide Compatibility: Supports 12V, 24V, 36V, and 48V battery banks. LCD Display: Shows real-time voltage, time, and percentage. Serial Control (UART):
Allows for remote monitoring and parameter setting via a computer. Safety Protections:
Features include automatic power-off and time-limited charging to extend battery longevity.
For those looking to integrate this into a DIY solar project, you can find the module on sites like AliExpress
, though it is always recommended to refer to the specific physical manual included with your unit for precise wiring diagrams. or a list of UART serial commands for this module?
The XY-CD60 is a dual-mode DC voltage controller (6V–60V) designed for automated battery charging and discharge protection. It is commonly used as a voltage-sensitive relay to prevent overcharging or deep discharge in 12V, 24V, and 48V systems. 1. Setup and Quick Guide
Connection: Connect the battery or power source to the VIN+ and VIN- terminals. xycd60 manual
Mode Selection: Long-press the SET button to toggle between two primary modes:
P-1 (Charging Mode): Connect a charger to the input and a battery to the output. It stops charging when the upper voltage limit (UP) is reached.
P-2 (Discharging Mode): Connect a battery to the input and a load to the output. It cuts off the load when the lower voltage limit (dn) is reached to prevent over-discharge. Parameter Setting:
Short-press SET to cycle through parameters: UP (Upper limit), dn (Lower limit), OP (Conduction time), dOP (Delay start time). Use UP/DOWN buttons to adjust values. Long-press SET (approx. 5s) to save. 2. Key Specifications Voltage Range: 6V to 60V DC. Control Precision: 0.1V.
Maximum Current: Typically 10A for the standard XY-CD60, though variants like the XY-CD63 support up to 30A.
Safety Warning: The relay may "click" rapidly if the charging current is too high or the battery capacity is too small, causing the voltage to bounce between limits. 3. Operational Features LCD Display: Shows real-time voltage and settings.
Power Saving (L-P): Long-press the DOWN button to toggle the screen's auto-off mode.
Error Indicators: If the voltage exceeds settings, the relay will disconnect. Always ensure your charger voltage matches your battery system (e.g., use a 24V charger for a 24V battery) as the module does not change the voltage; it only acts as a switch.
For detailed technical drawings or specific wiring diagrams, you can refer to manuals hosted on Scribd or ICStation. What is your system voltage (12V, 24V, etc.)?
XY-CD60 Solar Battery Charge Controller Module - RoboFactory
The XY-CD60 is a dual-function battery controller module designed for DC 6V–60V systems. It acts as an automated switch to protect lead-acid or lithium batteries from overcharging and over-discharging by managing the connection between a power source (charger), the battery, and the load. Core Specifications Voltage Range: DC 6V to 60V.
Working Modes: Charging Control (P-1) and Discharging Control (P-2).
Protection Features: Overcharge protection, under-voltage protection, and voltage monitoring.
Display: LCD screen showing voltage, percentage (calculated as
), and status symbols like "IN" (charging) or "OUT" (discharging). Operating Modes
The module supports two primary configurations based on your setup: Charging Control (P-1):
Setup: Connect a charger to the input and a battery to the output.
Operation: The relay closes (starts charging) when battery voltage drops below the Lower Limit (dn). It opens (stops charging) when voltage exceeds the Upper Limit (UP). Discharging Control (P-2):
Setup: Connect a battery to the input and a load to the output.
Operation: The relay closes (powers the load) when battery voltage is above the Upper Limit (UP). It opens (cuts power) when voltage falls below the Lower Limit (dn) to prevent deep discharge. Setup and Programming
Follow these steps to configure the XY-CD60 module according to its manufacturer instructions from IC Station: User Guide: XY-CD60 Battery Charge and Discharge Controller
Mode Selection: Long-press the SET button to toggle between P-1 and P-2 modes.
Setting Limits: Short-press SET to cycle through parameters: UP: Upper limit voltage. dn: Lower limit voltage. OP: Turn-on time (optional delay).
Adjusting Values: Use the UP and DOWN buttons to increase or decrease values.
Error Handling: If "ERR" flashes, it indicates the lower limit (dn) is set higher than the upper limit (UP). Safety and Installation Notes
Battery Requirement: If no battery is detected at the output during charging mode, the screen will display "nbE" and 0.00V.
Load Constraints: Ensure the load connected to the output does not exceed the relay's rated capacity (typically 10A–30A depending on the specific sub-model variant).
Mounting: The unit should be kept in a dry, dust-free area away from direct sunlight for optimal performance. 24V lithium battery setup?
XY-CD60 Solar Battery Charge Controller Module - RoboFactory
The is a versatile 6V-60V DC battery controller designed to protect both batteries and loads by managing charge and discharge cycles.
While it's often sold as a "charger," it is actually a voltage-controlled switch (relay) that does not change voltage or limit current itself; those are determined by your external charger or power source. Key Functional Modes
According to technical summaries from RoboFactory and ICStation, the module operates in two primary modes:
Charging Control (P-1): Prevents overcharging. When the battery voltage drops to a user-set lower limit (dn), the relay closes to begin charging. Once it hits the upper limit (UP), the relay opens to stop.
Discharging Control (P-2): Protects against over-discharge (undervoltage). The relay stays closed to power the load until the battery hits the lower limit (dn), at which point it disconnects to prevent battery damage. Interesting Technical Highlights
Forced Start Timer (0-10s): A unique feature mentioned in eBay listings allows for a "forced start" to account for instantaneous voltage drops when a heavy load first turns on, preventing the controller from immediately tripping into protection mode.
Delayed Turn-On: You can set a delay (0-999 seconds) between cycles, which is useful for allowing batteries to stabilize or "rest" between charge and discharge phases.
Real-Time LCD: The screen displays voltage, battery percentage (calculated as ), and even the total operating time for the current cycle. Common Applications
The XY-CD60 manual (hosted on Scribd) notes its popularity in:
XY-CD60 Solar Battery Charge Controller Module - RoboFactory
Enter Settings Mode: Long press the SET button to enter the parameter setting interface.
Switch Parameters: Short press the SET button to cycle through the parameters you wish to change.
Adjust Values: Short press or long press the UP/DOWN buttons to increase or decrease the parameter values. Power Button : Turns the CD player on and off
Save and Exit: Long press the SET button for approximately 5 seconds to save your values and return to the main interface. Working Modes
Charging Control Mode (P-1): The relay turns on when the voltage is below the lower limit (dn) and turns off when the voltage reaches the upper limit (UP).
Discharging Control Mode (P-2): The relay turns on when the voltage is above the upper limit (UP) and turns off when it drops below the lower limit (dn). Additional Features
Charging Time Control (OP): You can set a specific duration for charging. If the voltage does not reach the upper limit within this time, the relay will automatically disconnect.
Turn-on Delay (dLE): Adds a delay (in seconds) between reaching the activation voltage and the relay actually closing.
Force Turn-on (on): Allows for manual activation of the relay for testing purposes.
The XY-CD60 is a DC 6V–60V battery charge and discharge controller designed to automate battery maintenance and prevent damage from overcharging or deep discharging. It functions as a voltage-sensitive relay, acting as an automated switch between your power source and the battery. 🛠️ Key Specifications Operating Voltage: DC 6V–60V. Maximum Current: Generally rated for 10A through the relay. Control Precision: 0.1V. Modes: Charging (P-1/IN) and Discharging (P-2/OUT).
Protection: Overload, undervoltage, and overcharge protection. 📋 Operating Modes
Here’s a general write-up / user manual summary for a device labeled XY-CD60 (commonly a programmable digital voltage / current control module, often used for battery charging, power supply control, or over/under voltage protection).
If you have a specific XY-CD60 model (e.g., XY-CD60L, XY-CD60H, or a different variant), let me know and I’ll adjust the details.
The XYCD-60 is a dual-display, dual-output temperature controller. It is commonly used in incubators, refrigeration units, fermentation chambers, and industrial heating/cooling applications. Its primary feature is the ability to control two separate processes simultaneously or control a single process with both heating and cooling mechanisms.
Key Specifications:
The XYCD-60 features screw terminal blocks. Always disconnect power before wiring.
A. Power Input
Locate the terminals marked for power (often labeled L, N, and Ground or simply AC).
B. Sensor Input
Locate the sensor terminals (often labeled NTC, IN, or marked with a sensor icon).
C. Output Terminals (Relays) The XYCD-60 usually has two sets of output relays (Output 1 and Output 2). Each set typically has three terminals:
Example Wiring for a Heating Device (to Output 1):
| Measurement Type | How to Do It | Common Mistake | |----------------|--------------|----------------| | External (Outside diameter) | Slide open the larger lower jaws, place around the object, close gently. | Applying too much pressure (skews reading by +0.1mm). | | Internal (Inside diameter) | Use the upper smaller jaws (top of caliper). Insert into hole, expand until contact. | Reading the wrong scale (use the top LCD number). | | Depth | Extend the depth rod from the bottom end. Place caliper body perpendicular to the hole. | Tilting the caliper (adds false depth). | | Step | Use the front edge of the main jaw (where the step is). | Forgetting to zero before a step measurement. |
The controller typically features a four-button interface:
This feature is rarely explained in the basic XYCD60 manual but is powerful:
12V Lead-acid battery low-voltage disconnect
Detailed Product Guide and Manual: XYCD-60 Dual-Output Temperature Controller
Please note: The XYCD-60 is a widely manufactured generic temperature controller. While this guide covers the standard hardware and functionality, specific wire color codes or port layouts may vary slightly between production batches. Always verify the markings on your specific device's terminal blocks before final wiring.