Contact Us
DDM Garage Doors, Inc.
1092 Carolina Dr. Unit 5
West Chicago, IL 60185
Fax
(630) 293-1526
To reset the password for a Traice DVR, you typically need to use a dynamic password generated based on the system's current date or its serial number. Since "Traice" is often a rebranded or white-label OEM product (frequently using XMeye or Dahua firmware), the most reliable recovery methods involve software-based super passwords or physical hardware resets. Method 1: Dynamic Super Password (Recommended)
Most Traice-compatible systems use a "Super Password" based on the internal system date.
Check the DVR Date: Look at the date and time displayed on your monitor (e.g., 2026-04-16).
Generate a Code: Use a standard DVR password generator. For many XMeye/Traice boards, codes are generated based on YYYYMMDD.
Common Universal Codes: Try default combinations like 000000, 111111, 123456, or 888888 first [23].
Enter the Code: Type the generated super password into the login screen. This should bypass the user lock and allow you to set a new admin password. Method 2: Serial Number Recovery
If the date method fails, you can use the device's unique serial number.
Locate the Serial Number: Go to the login screen and click "Forgot Password" or look for an information icon. Note the Serial Number (S/N) or Device ID [18].
Contact Support: If you cannot find a generator tool (like GenSuperPassword.exe), you may need to take a photo of this screen and email it to the manufacturer or your local distributor to receive a one-time unlock code [24]. Method 3: Physical Hardware Reset
If software methods are unavailable, a manual factory reset is required.
Motherboard Reset Button: Open the DVR casing and look for a small push-button labeled "RESET" or "SW1" on the motherboard. With the power off, hold the button, plug the power in, and keep holding for 15–30 seconds [4, 21].
CMOS Battery Removal: Unplug the power and remove the round silver battery (CR2032) from the motherboard for at least 3 minutes. This often reverts the system date to a factory default (e.g., 2000-01-01), which allows you to use a known default password for that specific date. Summary of Common Default Credentials Brand/Firmware Default Username Default Password Traice / XMeye admin (blank) or 123456 Dahua OEM admin admin Hikvision OEM admin 12345 or password traice dvr password reset
Important Note: Performing a factory reset may erase your network settings and recording schedules, but it typically does not delete recorded footage on the hard drive [19, 22].
The following story illustrates a typical scenario for resetting a Traice DVR (often rebranded or similar to common H.264 network DVRs) when a password is lost. The Locked Lens: A Reset Story
Marcus sat in his small office, staring at the login screen of his Traice DVR. It had been months since he last needed to check the footage, and the password he thought he knew—a combination of his old dog’s name and birth year—wasn't working. After three failed attempts, the system began to mock him with "Account Locked."
He knew he had two options: the "Soft Reset" via the interface or the "Hardware Reset" involving the machine's guts. The Digital Key Search
First, Marcus tried the digital route. He clicked on "Forgot Password". The screen popped up with a Serial Number and the current system date. He remembered reading that some technicians use a "Super Password" generator. He grabbed his phone and searched for a DVR password calculator.
By entering the date displayed on the DVR (which had drifted back to 2000-01-01), the tool gave him a temporary six-digit code. He held his breath and typed it in. Invalid. The Traice firmware was newer than the old calculator could handle. The "Battery" Trick
Determined, Marcus grabbed a screwdriver. He unplugged the power, unscrewed the casing, and peered inside. There, nestled on the green motherboard, was a small, silver CMOS battery. He carefully popped the battery out using a small flathead.
He waited for a full minute to let the internal capacitors drain. He reinserted the battery and plugged the power back in.
As the DVR chimed to life, the date had reset to the factory default. He tried the classic default login: Username admin with a blank password, or sometimes 12345. This time, the menu opened. Success and Security
Marcus immediately went to the Account Settings. He didn't want to do this again, so he created a new, strong password and, more importantly, took a photo of the recovery QR code provided by the system for future resets. He closed the metal casing, tightened the screws, and finally watched the footage he needed. Common Reset Methods for DVRs
If you are currently facing a lockout with a Traice or similar DVR, these are the most reliable methods: To reset the password for a Traice DVR
Default Passwords: Try admin (blank), 123456, 888888, or 000000.
CMOS Battery Removal: Unplugging the internal battery for 1-5 minutes often resets the system clock and password to factory defaults.
Hardware Reset Button: Look for a small "Reset" button on the motherboard. Hold it for 15 seconds while powering the unit on.
Super Password Generators: Use the serial number and the date shown on the monitor to generate a one-day master code via support sites.
In the quiet town of Sterling Oaks, , a retired archivist, found himself locked out of his own memories—or at least, the digital version of them. His Traice DVR
system, which held the only footage of his prize-winning garden from the previous summer, was firmly rejecting his password.
"I could have sworn it was the dog's birthday," he muttered, clicking the mouse in frustration.
The screen blinked a cold, red "Invalid Password." Silas knew he had to act before the next storm wiped the system's current feed. He pulled up his notes and began the "Ritual of the Reset." 1. The Quest for the Secret Questions
Silas remembered the day he installed the unit. He had set up security questions specifically for a moment of forgetfulness like this.
He right-clicked the mouse to bring up the main menu and clicked the for settings. He selected "Forgot Password" and chose the option to reset via security questions. The screen asked: "What was your first pet's name?" Silas typed "Buster" with trembling fingers. Success. The system prompted him for a new password
. He chose something he'd never forget—the coordinates of his favorite fishing hole—and typed it in twice to confirm. 2. The Internal Reset (The "Hard" Way) Check the Date/Time Battery: Inside the DVR is
But Silas’s neighbor, Miller, hadn't been so lucky with his own unit. Miller's Traice model didn't have security questions enabled. He had to go "under the hood." Miller had to unscrew the top cover of his DVR to reveal the green motherboard. He located the small, silver CMOS battery
(about an inch in diameter) that kept the internal clock and memory running. Using a plastic tool, he carefully popped the battery out
To ensure the memory was fully "cleared," he used a small piece of insulated wire to bridge the positive and negative contacts for five minutes, discharging any leftover power.
After reinserting the battery and rebooting, the system reverted to its factory default password —usually 3. The Digital Key
For those who preferred code over screwdrivers, Silas’s nephew, a tech-savvy teen, suggested the GUID method This involved plugging a
into the DVR and clicking "Export" to save a unique encrypted file.
That file was then emailed to technical support, who would send back a "Reset Key".
Once imported, the DVR would bow to its owner once more, allowing a fresh password to be set.
By sunset, Silas was back in the system. The footage of his blooming peonies played across the screen, a digital victory in a world of forgotten codes. exact default codes
for specific Traice model numbers to see if they work for your unit? How to Reset DVR Password
If you have tried all the methods above and the Traice DVR still rejects your password:
admin):
888888666666abcd1234tljwg0w1 (Yes, seriously – this is a known universal code for many OEM DVRs).Huge inventory of torsion springs for same or next day shipping! Here you will find all you need in the most common sizes of 1 3/4," 2," 2 1/4," and 2 5/8" inside diameter springs. Larger 3 3/4" and 6" inside diameter commercial and industrial springs may require a day or two to ship. You'll also find TorqueMaster Springs, Extension Springs, Self-Storage door springs, steel rolling door springs and springs for one piece single panel doors.
Shelves packed with every part you need to fix your doors.
Please note. Shipping times and costs have changed. Normal transit times are currently not guaranteed, even on next day and second day shipments. Shipping prices on items over eight feet have more than tripled.
