Sunlu T3 Firmware ◆

Inside the Sunlu T3: A Look at the Firmware Driving the Slicer-Detector

The Sunlu T3 is distinct in the budget 3D printer market primarily for its "Slicer-Detector" functionality—a built-in sensor designed to detect clogs and filament runout. While the hardware often gets the spotlight, the firmware is the critical component that dictates how these sensors behave and how the printer manages thermal stability.

Here is a breakdown of the Sunlu T3 firmware landscape, common issues, and what users need to know.

6. Storage & File Management

  • SD Card (Primary): Supports FAT32 format. Recognizes long filenames (but character limit is ~50).
  • USB (Print via PC): Standard serial interface (115200 baud). Supports M112 (emergency stop) and M500 (save settings).
  • File navigation: Folder browsing is supported, though slow to scroll.

Upgrading the LCD Firmware (DWIN Set)

This is the step most users forget. The Sunlu T3 has a separate microcontroller on the LCD screen (usually a DWIN or DACAI screen). If you update the mainboard firmware but not the screen firmware, you may see: sunlu t3 firmware

  • Garbled text.
  • Missing icons.
  • A UI that displays temperatures but won't respond to clicks.

To update LCD firmware:

  1. Format an SD card (must be small, 1GB-8GB).
  2. Copy the DWIN_SET folder (containing .bmp and .bin files) to the card.
  3. Insert the SD card into the back of the LCD screen (not the mainboard slot).
  4. Power on the printer. The screen will turn blue and flash for 10 seconds.
  5. Power off and remove the SD card.

2. Leveling & Probing System

  • Manual Mesh Bed Leveling (3x3 or 4x4): The T3 does not come with an auto-level probe (BLTouch optional), but the firmware fully supports manual mesh.
  • Feature: The Level Bed menu guides you to 9 points. It saves the mesh to EEPROM.
  • Live Z-Offset: During printing, you can enter the Tune menu and adjust the Z-offset in 0.025mm increments. This is critical for first-layer success.

📥 Known firmware versions floating around

  • V1.0.4 – original factory version.
  • V1.1.2 – adds thermal runaway protection improvements.
  • V1.2.0 – fixes homing and Z-offset saving.

4. Filament Handling Features

  • Filament Runout Sensor: The firmware includes the logic for a runout sensor (the hardware is optional/aftermarket on some T3 models).
    • Behavior: Pauses print, retracts filament slightly, moves head away. Resume after load.
  • Change Filament (M600): A dedicated menu option. It will:
    1. Park the nozzle.
    2. Eject the old filament.
    3. Beep until you load new filament.
    4. Purge 10-30mm.
    5. Resume.

11. Minimal Troubleshooting Checklist

  • Incorrect temps → confirm thermistor type in firmware.
  • Axis moves reversed → flip motor connector or change invert in firmware.
  • No display → check cable and display model match firmware.
  • Upload fails → install drivers, try different USB cable, or use ISP.

If you’d like, I can:

  • Provide a step-by-step flash guide tailored to your exact board if you upload photos of the mainboard and display, or
  • Search for specific Sunlu T3 firmware releases (I can run a web search).

(End)

Here’s a draft for a forum or Reddit-style post about Sunlu T3 firmware. You can adjust the tone depending on where you’re posting (e.g., r/3Dprinting, Sunlu community, Facebook group). Inside the Sunlu T3: A Look at the

Title: Sunlu T3 firmware – where to find it and how to update?

Body:

I’ve been trying to locate the official firmware for the Sunlu T3 (which is essentially a rebranded/slightly modified Ender 3 variant). So far, the info seems scattered. Here’s what I’ve gathered – please add if you know more.

Scroll to Top