Life Probo PR70 is an electromechanical operator designed by Life Home Integration
for sectional and up-and-over garage doors. The 10-page manual covers everything from the initial mechanical setup to electronic programming. www.homelife.it Key Installation Steps Preparation
: Ensure the door is balanced and moves freely. For up-and-over doors, you must use the APRB oscillating curved arm Motor Mounting Open the operator hatch and remove the cap. Unscrew the omega-shaped brackets
and mount the operator onto the runner, ensuring the protruding shaft fits correctly into the block.
Fasten the unit back to the runner using the four hexagonal screws provided. Positioning
: The runner must be level. The minimum vertical distance between the door and the ceiling should be Mechanical Stops closing mechanical stop
by pulling the release lever and resting the gate closed against the drive carriage. Repeat for the opening stop at your desired open position. Programming & Usage One-Touch Setup : To calibrate the door's travel, press and hold the start button
(or the blue button depending on the model version) until the LEDs light up. The motor will perform a sequence of closing and opening to learn the limits automatically. Adding Remotes : Briefly press the blue button
, then press the button on your remote control to register it. Manual Release : In case of power failure, pull the cord on the drive carriage (release lever)
to move the door by hand. To re-engage, return the door to its original position until it "clicks" back into the transmission. Maintenance Safety Checks : Periodically check that the obstacle detection is working. You can adjust the sensitivity by holding the red button for five seconds and using the plus/minus keys.
: All maintenance or wiring adjustments must be done with the power supply disconnected.
For the full detailed diagrams and technical specifications, you can view the Probo PR70 PDF Manual from Peiter.pl or Montaza.lv
Are you setting up a new unit from scratch, or are you trying to troubleshoot a specific issue like remote programming? How to program Probo XL 4 Jun 2024 —
This report outlines the essential technical, installation, and maintenance requirements for the LIFE Home Integration Probo PR70, an irreversible electromechanical operator designed for residential sectional and up-and-over garage doors. 1. Technical Specifications
The Probo PR70 is powered by a 24V DC motor with a 230V AC mains supply. Maximum Leaf Area: Up to Maximum Door Width: 5.0 meters. Thrust: 650 N. Operating Temperature: -20∘Cnegative 20 raised to the composed with power C +70∘Cpositive 70 raised to the composed with power C
Safety Features: Built-in encoder for obstacle detection and a manual release mechanism. 2. Installation Guide
Installation must be performed by a professional fitter to ensure legal compliance. Preliminary Checks:
Ensure there is sufficient clearance for maintenance and manual release operations.
For up-and-over doors, an APRB curved oscillating arm is required. Life Probo PR70 is an electromechanical operator designed
The vertical distance between the door and the ceiling must be at least 40 mm. Motor Mounting:
Open the operator hatch and loosen the clamping screws to remove the protective cap. Remove the "omega-shaped" support brackets.
Insert the operator's shaft into the runner block without forcing the tab.
Secure the motor to the runner using the brackets and provided hexagonal screws. Ceiling Attachment: Fix the front part of the runner to the lintel or ceiling.
Lift the runner until it is parallel to the ceiling and mark fixing holes for the rear brackets.
Secure the rear brackets firmly with suitable screw anchors. 3. Programming and Use
Initial setup calibrates the door's travel limits and force settings.
Initial Setup: Hold the Start button for 5 seconds until all LEDs illuminate. Pressing it again initiates a self-learning cycle where the door opens and closes to identify mechanical stops.
Adding Remotes: Briefly press the Blue button, then the transmitter button, and press the Blue button again to register. Adjustment Options:
Yellow Button: Adjusts automatic closing time (options range from 5 to 120 seconds).
Red Button: Adjusts force levels and obstacle detection sensitivity. 4. Maintenance and Troubleshooting
PROBO PR70 PR70-DL PR120 PR120-DL - Automatizari pentru porti
Life Pro Bio PR70 Installation, Use, and Maintenance Manual
Table of Contents
Page 1: Introduction
The Life Pro Bio PR70 is a high-performance bioreactor designed for research and development applications. This manual provides instructions for the installation, use, and maintenance of the Life Pro Bio PR70. It is essential to read and understand this manual before operating the device to ensure safe and effective use.
Page 2: Safety Precautions
Page 3: Installation Instructions
Page 4: Operating Instructions
Page 5: Maintenance Schedule
Page 6: Troubleshooting
Page 7: Replacement Parts
Page 8: Technical Specifications
Page 9: Warranty Information
The Life Pro Bio PR70 is covered by a limited warranty for a period of one year from the date of delivery.
Page 10: Conclusion
The Life Pro Bio PR70 is a reliable and high-performance bioreactor designed for research and development applications. By following the instructions in this manual, users can ensure safe and effective operation of the device. Regular maintenance and troubleshooting can help prevent issues and extend the lifespan of the device.
This guide provides a comprehensive overview of the Life Probo PR70
, an irreversible electro-mechanical operator designed for sectional and up-and-over garage doors. 1. Preliminary Installation Checks
Before starting, ensure your door is in good mechanical condition, balanced, and operates smoothly by hand.
Space Requirements: The installation area must have enough room for maintenance and manual release. Door Limits: The
is suitable for doors with a maximum width of 5 meters, provided they are perfectly balanced.
Clearance: For sectional doors, maintain a minimum vertical distance of 40 mm from the ceiling and between 10 and 65 mm from the operator runner. 2. Mechanical Assembly
The operator must be properly mounted on its runner (rail) before ceiling installation.
Open the Hatch: Loosen the clamping screws (2) and remove the operator cap (3) from the base.
Remove Brackets: Unscrew the four screws (6) to remove the omega-shaped support brackets (5). Page 1: Introduction The Life Pro Bio PR70
Mounting: Insert the protruding shaft of the operator (8) into the block's hole (9) on the runner without forcing it.
Securing: Fasten the operator back to the runner using the omega-shaped brackets and the original hexagonal screws. 3. Setting Mechanical Stops
Closing Stop: Pull the release lever to close the gate, rest the mechanical stop against the drive carriage, and fix it in place.
Opening Stop: Open the gate to your desired stop point, rest the opening mechanical stop against the carriage, and secure it. 4. Programming and Calibration
Modern Probo units often feature a "One-Touch" or automated setup sequence.
Initial Setup: Press and hold the start button for five seconds until all LEDs between the plus (+) and minus (-) signs light up.
Self-Learning: Press the start button again. The door will perform a sequence—closing, opening, and closing—to find its mechanical stops and calibrate the stroke.
Confirmation: The green LEDs will flash once the stroke is saved.
Remote Pairing: Briefly press the blue button, transmit a signal from your remote, and press the blue button again to register it. 5. Maintenance and Safety
Manual Release: In case of power failure, pull the cord connected to the mobile trolley to move the door by hand. To reconnect, return the door to its initial position until it hooks back up.
Obstacle Sensitivity: To adjust how easily the door reverses when hitting something, hold the red button for five seconds and use the +/- buttons to set the level.
Safety Warning: Always disconnect the power before performing maintenance. If the power source is not in view, display a sign stating "ATTENTION: MAINTENANCE WORK IN PROGRESS". How to program Probo XL
Note: This document is a template. Specific technical specifications (exact PSI ratings, voltage, filter part numbers) should be verified against the manufacturer’s technical data sheet before final printing.
Technical specifications table (flow rate 70 L/min, power 750W, IP54, 230V~50Hz).
Checklist before installation:
User interface (LCD):
Normal operation:
What to monitor:
Energy saving tip: Set P1–P2 difference ≥ 1 bar to reduce starts/hour.