Life Probo Pr70 Instructions For Installation Use And Maintenance Manual 10 Pages Upd ((install)) • Confirmed

Page 1: Cover Page

Documentation and Support

By following these guidelines, users can ensure the Life Probo PR70 operates effectively and safely, providing accurate and reliable patient monitoring. Always consult the device's manual for specific instructions and any updates.

Life Probo PR70: The Ultimate Guide to Installation, Use, and Maintenance

The Life Probo PR70 is a robust and reliable electromechanical actuator designed for sectional and spring-balanced doors. To ensure your garage door automation system operates safely and efficiently for years to come, following the official manual is essential.

This comprehensive guide breaks down the critical components of the 10-page updated manual, covering everything from initial mounting to long-term care. 1. Pre-Installation Checklist Before unboxing your Life Probo PR70, verify the following:

Door Condition: The door must be perfectly balanced and move smoothly manually.

Space Requirements: Ensure there is enough clearance between the ceiling and the highest point of the door's travel.

Power Supply: A grounded 230V power outlet should be available near the motor head. 2. Mechanical Installation

The installation is the foundation of your system’s performance.

Assembling the Track: Join the rail sections (chain or belt) according to the manual's diagrams. Ensure the tension is firm but not overly tight. Page 1: Cover Page Documentation and Support

Mounting the Rail: Attach the front header bracket to the wall above the door and the rear bracket to the ceiling.

Attaching the Motor Head: Slide the Probo PR70 head onto the rail and secure it with the provided bolts.

Connecting the Arm: Link the door bracket to the trolley using the straight and curved arm assembly. 3. Wiring and Electrical Connections

Control Board Access: Remove the protective cover to access the terminal blocks.

Photocells & Safety: Connect your safety beam sensors to the designated terminals. The Probo PR70 features an auto-stop mechanism, but external photocells are highly recommended.

Wall Switch: (Optional) Connect a wired push-button if you prefer manual control inside the garage. 4. Programming and Limits

The updated 10-page manual emphasizes the "Auto-Learning" feature:

Setting Travel Limits: Use the control buttons on the motor head to define the "Open" and "Closed" positions. Manual : Keep a copy of the manual handy for reference

Force Adjustment: The PR70 automatically calculates the force required to move the door. This ensures the motor stops instantly if it hits an obstruction.

Remote Pairing: Press the 'Radio' button on the board and then the button on your Life Fido transmitter to sync them. 5. Daily Use and Features

Manual Release: In case of a power outage, pull the cord on the trolley to disconnect the motor and move the door by hand.

Soft Start/Stop: The PR70 is programmed to slow down at the end of each cycle, reducing noise and wear on the door hardware. 6. Maintenance and Troubleshooting

To keep your Probo PR70 in peak condition, follow this maintenance schedule:

Monthly: Test the safety reversal system by placing an object in the door's path.

Every 6 Months: Check the rail tension and lubricate the door hinges and rollers (do not grease the rail itself if it is a belt drive).

Troubleshooting: If the light flashes, refer to the "Error Codes" section in the manual. Common issues usually involve misaligned photocells or a change in door balance. Important Safety Note By following these guidelines, users can ensure the

Always disconnect the power supply before performing any maintenance or opening the control unit cover. If you are unsure about any step, consult a professional installer.

The Life Probo PR70 is an irreversible electromechanical operator designed for residential sectional and up-and-over garage doors. The 10-page instruction manual provides a comprehensive guide for professional fitters on installation, programming, and maintenance. Core Technical Specifications PR70-07 / PR70-DL Details Power Supply 230 Vac 50 Hz (Mains) / 24 Vdc (Motor) Max Leaf Surface Up to 11.5 m² Thrust Force 650 N to 700 N Operating Temp -20°C to +70°C Safety Built-in encoder and electronic control unit Protection IP20 or IP54 depending on the specific model variation Key Features for Installation & Use How to program Probo XL

PAGE 8: MAINTENANCE – CLEANING & DESCALING

Weekly External Cleaning

Monthly Descaling (if water hardness > 120 ppm)

  1. Fill a container with 500ml of white vinegar + 500ml water.
  2. Remove the filter cartridge. Place the intake hose into the vinegar solution.
  3. Run the PR70 in “Flush” mode for 3 minutes. Let sit for 30 minutes.
  4. Rinse by running fresh water (without filter) for 5 minutes.
  5. Reinstall the filter, reset timer, and flush again.

Cleaning the Nozzle/Spout

Long-term Storage ( >1 month)

6.5 Replacement Parts Table

| Part Number | Description | Replacement Interval | |-------------|-------------|----------------------| | PR70-P1 | Sediment + Carbon Pre-filter | 90 days / 500 gal | | PR70-P2 | RO Membrane (400 GPD) | 12 months | | PR70-P3 | Post-carbon / UV Lamp | 12 months | | PR70-AF | HEPA+Active Carbon | 6 months (air version) |

Page 5: Electrical & Smart Setup

5.3 Reading the Display Icons

LIFE PROBO PR70