Kirisun Programming Software Pt8100 < 720p · 4K >

It can be difficult to find a single "definitive" user manual for Kirisun software online, as the company often distributes disks with the hardware. However, I have compiled a comprehensive guide article below.

This article covers the specifics of the Kirisun PT8100 programming software, including setup, critical settings, and troubleshooting tips. kirisun programming software pt8100

Export Restrictions

Kirisun software sometimes contains encryption features (ARC4, AES). Exporting such software without a permit from your local trade authority may violate export control laws. It can be difficult to find a single

2. Key Features of the PT8100 Software

• Frequency & Channel Programming: Set up to 256 channels (16 zones × 16 channels). Define RX/TX frequencies, QT/DQT (CTCSS/DCS) tones, bandwidth (12.5/25 kHz), power level (High/Low), and time-out timers.
• Zone Management: Organise channels into logical zones (e.g., “Dispatch”, “Maintenance”, “Emergency”).
• Signalling Support: Built-in support for 2-Tone, 5-Tone, DTMF, and optional MDC1200 (depending on firmware version).
• Scan Lists: Create custom scan lists (priority, revert channel, talkback).
• Advanced Features:
  • Lone worker
  • Man-down (if equipped)
  • Encryption (basic or optional AES)
  • PTT ID (encode/decode)
  • Stun/kill/revive commands
  • Emergency alarm and call setup
• Clone Function: Copy configuration from one PT8100 to another via programming cable.
• Firmware Update: Allows radio firmware upgrades (requires separate firmware file).

Part 3: Hardware Requirements for Programming

Before you install any software, you need the correct hardware. Programming a PT8100 is not done via USB directly into the radio. You require: " your COM port is wrong

1. A Windows PC (32-bit or 64-bit): While the software runs on 64-bit, driver compatibility is easier on 32-bit Windows 7/10.
2. Kirisun PT8100 Programming Cable: This is a special USB-to-serial (or Serial-to-radio) cable. The PT8100 typically uses a K-plug (two-prong connector) or a single barrel connector. Do not confuse this with Baofeng or Kenwood cables; pinouts differ.
3. USB-to-Serial Driver (Prolific/FTDI): Most aftermarket cables use the Prolific PL2303 chip. You will need the correct driver for your OS.

Pro Tip: If you are using Windows 10/11, you may need to disable Driver Signature Enforcement temporarily to install legacy Prolific drivers.

4. Installation & Setup Steps

1. Download or insert CD containing the PT8100 CPS (e.g., PT8100_CPS_v2.0.3.exe).
2. Run installer as Administrator to allow driver access.
3. Complete installation – default path: C:\Program Files (x86)\Kirisun\PT8100 CPS\
4. Connect the programming cable to the PT8100’s side microphone/programming port (GX16 8-pin aviation connector).
5. Power on the radio (12V DC required; programming is possible while radio is on but not transmitting).
6. Install USB drivers if prompted (check Device Manager for COM port number).
7. Launch the software – you will see a blank channel grid.

Product scope and typical use cases

• Devices: PT8100 handheld radios (single- and multi-channel variants) used in industries like security, manufacturing, hospitality, and event operations.
• Primary uses: frequency/channel configuration, contact lists/group calls, power and signaling settings, encryption/key management (if supported), firmware flashing, and backup/restore of radio profiles.
• Environments: mass-deployment staging labs, on-site fleet updates, repair centers, and periodic compliance/audit checks.

Part 5: How to Program the Kirisun PT8100 (Walkthrough)

Now for the core task: programming channels.

1. Connect the Radio: Ensure the PT8100 is powered OFF. Connect the programming cable to the radio’s mic/speaker jack.
2. Launch the Software: Open the Kirisun PT8100 CPS.
3. Read the Radio: Go to Program > Read from Radio (or press F3). Turn the radio ON when prompted. The software will read the current codeplug (the radio’s brain). Always read first – never write a blank file to the radio.
4. Backup the Original Codeplug: Immediately save the read data as PT8100_Backup_Original.dat. If you mess up, you can revert.
5. Edit Channels:
   • Navigate to the Channel Information or Zone tab.
   • You will see rows for Channel 1, 2, 3, etc.
   • Rx Freq: Input the receive frequency (e.g., 462.562500).
   • Tx Freq: Input the transmit frequency (if duplex) or leave same as Rx for simplex.
   • QT/DQT Enc/Dec: Set your CTCSS (e.g., 67.0 Hz) or DCS code.
   • Power: Select High (4-5W) or Low (1W).
   • Busy Lock: Set to Carrier or QT/DQT to prevent channel interruptions.
6. Write to Radio: Click Program > Write to Radio (F4). Turn the radio off and on again as instructed.

Troubleshooting Write Errors: If you see "Communication Timeout," your COM port is wrong, or the cable driver is outdated. Try a USB 2.0 port (not USB 3.0), as legacy radios dislike USB 3.0 controllers.