Hyt Tc-500 Programming Software May 2026

The HYT TC-500 Customer Programming Software (CPS) is the essential tool for configuring the 16-channel, analog HYT TC-500 portable radio. It allows users to set specific frequencies, privacy codes, and operational parameters to optimize performance for industries like hospitality, security, and construction. Essential Requirements

Software: Specifically designed for the TC-5 series; commonly compatible with Windows-based PCs.

Hardware: Requires the PC26 USB programming cable (or the older PC19 serial cable). Hyt Tc-500 Programming Software

Drivers: Proper USB-to-serial drivers must be installed for the PC to recognize the radio connection. Core Programming Features

The software provides a graphical interface to adjust the following: TC-500 User Manual The HYT TC-500 Customer Programming Software (CPS) is

Step-by-Step Driver Installation (Windows 10/11):

1. Disable Driver Signature Enforcement (For old Prolific chips): Restart PC → Press F8 → Select "Disable driver signature enforcement."
2. Install Old Driver: Download PL-2303 Driver v3.2.0.0 (2008 version). Manually point Windows to this .inf file.
3. Identify COM Port: Go to Device Manager → Ports (COM & LPT). Note which COM port number the cable is using (e.g., COM3).
4. Set Port Speed: Right-click the cable → Properties → Port Settings → Bits per second: 9600 (default for TC-500) or 19200. Data Bits: 8, Parity: None, Stop Bits: 1.

Note: If you are using a genuine FTDI cable (more expensive), you do not need legacy drivers.

The Best Alternative: Hyt TC-500S and CPS Software

While this guide focuses on the standard TC-500, many users confuse it with the TC-500S. The 'S' model requires different CPS (Customer Programming Software). Do not attempt to use TC-500 software on a TC-500S; you will brick the radio’s logic board. Always verify your radio model before downloading software. Note: If you are using a genuine FTDI

Supported Software

• CPS (Customer Programming Software) — vendor-supplied Windows application used to program the TC-500 family. Commonly named “TC-500 CPS” or included in a generic Hyt/Hytera/Hytera-derivative CPS pack.
• USB/Serial driver — required for PC-to-radio connection (e.g., Prolific PL2303 or FTDI drivers depending on cable).
• Firmware upgrade tools — separate utilities (often included with CPS) for updating radio firmware.

Why Use the Software?

Attempting to program a radio manually (using the buttons on the device) is often tedious and limited. The software provides several key advantages:

1. Channel Management: The TC-500 can hold multiple channels. The software allows you to name these channels (e.g., "Security," "Maintenance," "Channel 1") rather than just seeing a number on the screen.
2. Frequency Precision: It allows for the exact input of TX (Transmit) and RX (Receive) frequencies, ensuring clear communication without interference.
3. CTCSS/CDCSS Tones: You can set private line codes (PL tones) easily. This ensures your team only hears communications meant for them, filtering out traffic from other users on the same frequency.
4. Feature Configuration: The software unlocks settings that are otherwise inaccessible, such as:
   • Time-out timers (preventing a user from hogging the channel).
   • Squelch levels.
   • Scan list configurations.
   • Battery save modes.

Step 5: Testing

Disconnect the cable. Turn the TC-500 off and on again. Key up the radio on channel 1 and use a second radio to verify the frequency and tone are correct.

Software

• Operating System: The HYT TC-500 software was developed during the era of Windows XP and Windows 7. While it often runs on Windows 10 and 11, users may occasionally need to run the program in "Compatibility Mode."
• Drivers: If using a USB programming cable, the correct drivers (often Prolific or FTDI drivers) must be installed on the PC before the software can recognize the radio.