Epson L3118 Resetter Adjustment Program Install ((hot)) -

Note on safety: I have included a disclaimer regarding the risks of using third-party resetter tools, as Epson does not officially endorse these for end-users.

Blog Title: Step-by-Step Guide: How to Install & Use the Epson L3118 Resetter (Adjustment Program)

Meta Description: Is your Epson L3118 showing a "Service Required" or ink pad overflow error? Learn how to download, install, and safely run the Adjustment Program (Resetter) to fix error 0xF5 or 0xF9.

Introduction

If you own an Epson L3118 EcoTank printer, you have likely fallen in love with its low-cost ink refills. However, like all Epson inkjet printers, the L3118 has a hidden "waste ink pad counter."

After months or years of cleaning cycles, the printer decides the pad is full and locks up with an error message like:

• “A printer’s ink pads are at the end of their service life.”
• “Service required. Parts inside your printer are near the end of their life.”
• Error code 0xF5 or 0xF9.

The official solution is to send it to a service center. The practical solution is the Epson L3118 Adjustment Program (Resetter). epson l3118 resetter adjustment program install

Warning: Using this program voids your warranty. Physically, the ink pads may actually be full and could leak. Only use this tool if you have reset the waste ink counter and cleaned/replaced the pads.

What is an Epson Adjustment Program?

Before diving into the installation, it is critical to understand what this software does. An Adjustment Program is a proprietary service tool designed by Epson for technicians. It allows you to:

1. Reset the waste ink pad counter – This is the primary function.
2. Initialize ink charging.
3. Perform print head alignment and nozzle checks.
4. Retrieve error logs.

Important Warning: Using this program voids your warranty if the printer is still under service coverage. It also does not physically clean the waste ink pads. You must either replace the pads or install a waste ink tank externally to prevent ink overflow. Note on safety: I have included a disclaimer

Pros & Cons

| Pros | Cons | |------|------| | Free (if found legitimately) | No official support | | Works offline | Can trigger antivirus false positives | | Resets permanent errors | Wrong use may brick printer | | No internet needed after download | Requires disabling driver signature checks (Windows) |

5) Step‑by‑step: Installing and using an adjustment/resetter program (generic, model‑specific notes for L3118)

Note: Steps below illustrate the general flow common to Epson adjustment utilities. Exact UI text varies by version.

1. Create a system restore point and backup important data.
2. (Optional, recommended) Snapshot the VM before proceeding.
3. Install Epson USB driver for L3118 and confirm the printer is detected in Devices and Printers.
4. Extract resetter package to a dedicated folder; right‑click and run the executable as Administrator.
5. If an installer is included, follow prompts. If the tool is a single executable, do not run more than one instance.
6. In the program, select your model (L3118) if a model list appears. If not listed, do not proceed — find the correct tool.
7. Click “Initialize” or “Select” to connect to the printer. The status field should show “COM” or “USB” and the printer status.
8. Choose the function: typically “Waste ink pad counter” → “Check” to read current value, then “Clear” or “Reset”.
9. After resetting counters, use the utility to perform nozzle check and head alignment/cleaning as required.
10. Power cycle the printer after completing operations.
11. Print a test page and run a nozzle check to confirm operation.

7. Important Warnings

• Do not click “EEPROM initialization” or “Head ID input” unless you have backup data.
• The resetter does not refill ink — you must manually refill tanks.
• After reset, the printer may still show low ink — that’s normal (ink level sensors are separate).
• Some counterfeit adjustment programs can brick the mainboard.

Step 3: Installing and Running the Program

Unlike standard software, the Adjustment Program usually does not have a traditional "Install" wizard. It is often a standalone executable file. Blog Title: Step-by-Step Guide: How to Install &

1. Open the extracted folder.
2. Look for the file named AdjProg.exe or Adjustment Program.exe.
3. Right-click the file and select "Run as Administrator."
4. If a security warning pops up, click "Run" or "Yes."

Step 4: Run the Program

• Right-click AdjProg.exe → Run as Administrator
• If a license window appears, enter (example):
  User: Epson / Key: 0000 or 1234567890 (varies by version)

Step 6: Reset Waste Ink Counter

• Go to Waste ink pad counter → Initial setting → Check → Initialization → OK
• After reset: Turn printer off → wait 10 sec → back on

Common Errors During Epson L3118 Resetter Adjustment Program Install

| Error Message | Solution | |---------------|----------| | “Communication error” | Printer is not in service mode. Re-enter service mode. Or change USB port. | | “Timeout error” | Disable firewall and antivirus completely. Run as admin. | | “Counter overflow” | The physical waste pad is full. You must clean or replace the pad before resetting. | | “Wrong model” | You downloaded a program for L3110 or L3150. Find the exact L3118 version. |