Caraflo V200 Shower Instructions (2026)

Caraflo V200 Shower System Instructions

Table of Contents

1. Introduction
2. Safety Precautions
3. Installation Requirements
4. Installation Steps
5. Operating Instructions
6. Maintenance and Cleaning
7. Troubleshooting

Introduction

Congratulations on purchasing the Caraflo V200 shower system! This user manual provides step-by-step instructions for safe and effective installation, operation, and maintenance of your new shower system.

Safety Precautions

• Always follow local plumbing regulations and codes.
• Ensure the shower system is installed and maintained by a qualified plumber.
• Use the shower system for its intended purpose only.
• Keep children and pets away from the shower area while it is in use.
• Never leave the shower unattended while it is in use.

Installation Requirements

• Water pressure: 1.5 - 10 bar (22 - 145 psi)
• Water temperature: 35°C - 60°C (95°F - 140°F)
• Pipe connections: 1/2" BSP
• Power supply: 230V, 50Hz (for electric mixer)

Installation Steps

1. Prepare the Wall: Ensure the wall is level, clean, and dry. Drill holes for the shower head, handle, and pipe connections.
2. Install the Pipe Connections: Connect the hot and cold water pipes to the shower mixer. Use a wrench to secure the connections.
3. Mount the Shower Mixer: Mount the shower mixer to the wall using the provided screws and wall anchors.
4. Install the Shower Head: Install the shower head to the wall using the provided screws and wall anchors.
5. Connect the Electric Mixer (if applicable): Connect the electric mixer to the power supply and pipe connections.

Operating Instructions

1. Turn On the Water Supply: Turn on the main water supply.
2. Adjust the Temperature: Use the handle to adjust the water temperature.
3. Select the Shower Mode: Select the desired shower mode (e.g., massage, normal).
4. Start the Shower: Press the shower head to start the water flow.

Maintenance and Cleaning

• Regularly clean the shower head and handle with a soft cloth and mild soap.
• Descale the shower system every 6 months to prevent mineral buildup.
• Check and replace worn-out parts (e.g., O-rings, seals) as needed.

Troubleshooting

• Low Water Pressure: Check for kinked or blocked pipes, and ensure the water supply is turned on.
• Leaking: Check for loose connections, worn-out seals, or damaged parts.
• Faulty Electric Mixer: Check the power supply and connections.

Warranty Information

The Caraflo V200 shower system is covered by a 2-year limited warranty. For more information, please refer to the warranty documentation provided with your purchase.

Conclusion

By following these instructions, you can ensure safe and effective installation, operation, and maintenance of your Caraflo V200 shower system. If you have any questions or issues, please contact our customer support team.

Caraflo V200 is a popular thermostatic shower mixer used extensively in static caravans and holiday homes (such as those by Swift or Willerby). Below are instructions for its installation, maintenance, and essential winter protection. Static Caravan Spares Installation Guidelines Positioning : The V200 can be fitted in either a horizontal or vertical orientation. Fixing Centres : The unit requires 45mm hole centres for mounting. Inlet Connections Connect the Hot supply to the inlet marked with 'H', a red/orange label, or "HOT". Connect the Cold supply to the inlet marked with 'C', a blue label, or "COLD". Prerequisite : Ensure all supply pipework is thoroughly flushed through

to remove debris before fitting the mixer to prevent damage to the thermostatic valve. Leisure Parts 4U Operating Specifications Temperature Range Hot supply: Cold supply: Water Pressure : Recommended operating pressure is between 0.5 and 5 bar Static Caravan Spares Maintenance & Seal Replacement

If the mixer begins to leak or was removed for winter, you may need to replace the O-ring seals. eBay Australia Drain Down : Turn off the water supply and drain the system. : Cover the shower drain to avoid losing small parts.

: Remove the small plugs (usually #8 in diagrams) to access fixing screws. Seal Fitting : Replace the Nitrile rubber O-rings on the wall-mounted brass tails. Lubrication : Lightly lubricate new seals with silicone grease The Shower Doctor Silicone Grease ) or mild soap before reassembly. The Shower Doctor Winter Protection (Crucial) Because the V200 is designed for holiday homes, it must be drained down or disconnected during winter to prevent internal damage. The Caravan Warehouse Freeze Warning

: Frozen water inside the tap expands and can crack the pipework or the internal thermostatic valve. caraflo v200 shower instructions

: If the home is left unheated, it is best to disconnect the mixer entirely and store it in a dry, frost-free location. The Caravan Warehouse troubleshooting guide for common caravan shower pressure issues? Caraflo V200 Shower Mixer Tap Thermostatic Chrome

Caraflo V200 is a thermostatic mixer shower valve specifically designed for leisure vehicles like static caravans, motorhomes, and holiday homes. It is an upgrade to the older V100 model, sharing the same 45mm pipe centres for a direct replacement without needing modification. The Caravan Warehouse Key Installation & Site Requirements For safe and optimal performance, the requires specific water conditions National Shower Spares Temperature Limits: Recommended maximum of 65 raised to the composed with power C , with a minimum hot water inlet of 55 raised to the composed with power C and a maximum cold inlet of 25 raised to the composed with power C Anti-Scald Protection: The mixed water temperature is typically preset between 35 raised to the composed with power C 40 raised to the composed with power C Fail-Safe Feature:

If either the hot or cold supply fails, the valve is designed to stop or significantly reduce the flow to prevent scalding or thermal shock. Supply Compatibility:

Do not mix a gravity-fed hot supply with a mains-fed cold supply (or vice versa). National Shower Spares Operating & Maintenance Instructions Water Control:

The valve uses a single handle or dial system to blend water. It maintains a consistent temperature even if water is used elsewhere in the vehicle (e.g., flushing a toilet). Winterizing (Critical): Because these are used in seasonal homes, the is designed for easy disconnection to prevent frost damage Turn off the main water supply to the caravan/motorhome.

Open all taps and the shower valve to drain remaining water.

Consider applying a non-toxic, caravan-safe antifreeze into the valve body to protect internal components. Cartridge Replacement:

If the shower drips or fails to regulate temperature, the internal thermostatic cartridge

(92mm length, 31.45mm diameter) may need replacement or descaling. Use silicone grease 3. Operating Instructions

when reinstalling or servicing the cartridge to ensure smooth operation. The Caravan Warehouse Replacement Spare Parts Caraflo V200 Shower Mixer Tap Thermostatic Chrome

Caraflo V200 is a thermostatic shower mixer valve commonly used in static caravans and holiday homes. Below are instructions for its installation, use, and winter maintenance. Installation Instructions

is designed to replace the older V100 model without needing modifications The Caravan Warehouse Orientation : It can be installed in either a horizontal or vertical Pipe Centers : It features standard 45mm pipe centers Water Connections : Connect the water supply to the inlet marked "H" (or red label) and the supply to the "C" inlet (or blue label). Preparation

: Always flush the supply pipework before fitting the mixer to prevent debris from damaging the thermostatic cartridge. Components

: A standard kit includes brass threaded tails, chrome back plates, an instruction manual, and a dedicated drain-down key Static Caravan Spares Operational Guidelines Temperature Range

: The thermostatic control provides a consistent temperature, typically factory-set at approximately . It can be adjusted during installation to a limit between 35°C and 45°C : For best performance, use water pressure between 0.5 and 5 bar

: Turn the flow control handle (often anticlockwise) to start the water, then adjust the temperature control. National Shower Spares Winter Maintenance & Draining

Because these units are often used in holiday homes, they must be protected from freezing, which can expand and damage the internal valve. The Caravan Warehouse V200 Caravan Shower Mixer Valve 45mm Centres Caraflo

You can use this text for a user manual, a how-to guide, or an FAQ section. Required tools: drill

What’s in the box / required tools

• V200 shower unit with cover and pre-fitted pipe connector
• Shower handset, hose, and wall bracket
• Fixing screws and wall anchors
• User manual and warranty card

Required tools: drill, screwdriver, adjustable wrench, PTFE tape, spirit level, pipe cutters, voltage tester, insulation resistance tester (for installation checks).

Adjusting Temperature

• Rotate the temperature handle clockwise (towards the red indicator) to increase heat.
• Rotate the handle counterclockwise (towards the blue indicator) to decrease heat.
• Note: The valve is thermostatic, meaning it will automatically compensate for changes in water pressure (e.g., if a toilet is flushed elsewhere in the house) to keep your shower temperature consistent.

Part 2: Detailed Installation Instructions

Warning: While these are DIY-friendly, if your home has copper piping or requires altering the shower arm inside a tiled wall, consult a licensed plumber.

The Monthly Rinse (Preventative)

1. Fill a plastic bag with 50% white vinegar and 50% water.
2. Submerge the shower head face completely.
3. Use a rubber band to secure the bag over the head.
4. Leave for 2 hours only. (Leaving overnight will corrode the chrome finish.)
5. Remove the bag and turn the shower on full hot for 2 minutes to flush dissolved minerals.

3. Operating Instructions